Email

daniya@amantrading.co.in

Call Us

(+91) 98450 48673

Laticrete 305

Description

Substrate: The surface to be covered with Ceramic tile shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in: Walls – 3mm in 2.5m Floors – 1.5mm in 1.0m

Surface Preparation:

  • If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile
  • Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc
  • Dampen the wall before application of thin set adhesive
  • Clean the back of tile for any dust or coating

Mixing: The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm). Pour potable clean water in a clean container and then add the powder LATAFIX® 305 and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need.

Proportion: Approximately 1 bag of LATAFIX® 305 with 5-6 liters of water. Adjust quantity of liquid to obtain proper consistency.

Installation:

  • Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered.
  • Additional mortar is then applied with the notched edge of the trowel.
  • When installing large tiles, spread adhesive onto back of tile in addition to troweling material over surface to be tiled. Select proper type of notched trowel.

a) Thin Tiles upto size 300 X 300 mm (1’X1’), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm

b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm

c) Large Porcelain Tiles upto 600 X 600 mm (2’X2’) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm

  • The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
  • Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
  • Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.

Areas of Application Designed for internal floor applications

Suitable Substrates

  • Cement Mortar Beds
  • Cement Plaster
  • Brick Masonry
  • Cement Terrazzo

Certification

  • ANSI : Meets ANSI A 118.1 T
  • EN 12004/ISO 13007: C1T
  • IS 15477:2019 TYPE 1  T ADHESIVE
  • VOC: Practically Nil

Reviews

There are no reviews yet.

Be the first to review “Laticrete 305”

Your email address will not be published. Required fields are marked *

Stain Free

Easy To Maintain

Designer Tiles

Made In India

Category

Share on Social Media

Additional Information

A factory-made bagged cementitious polymer based powder, containing Portland cement
and silica sand, it can be mixed with water for installing small and medium size ceramic floor
tiles in interior areas using the thin set method of installation.

Grouped Product Short NameLaticrete 305
Packing20kg & 50kg Bags
ColourGrey
Coverage Area (sq. ft)Approx. 55-60 sq. ft. per 20 kg bag with a ¼” x ¼” (6mmx6mm) square notch trowel for a bed of 3mm.